ARTICLE IN ACADEMIC JOURNALS
| NO | DETAILS OF ARTICLE IN ACADEMIC JOURNALS |
|---|---|
| 1. |
Experimental Construction and Validation of Revised Drucker-Prager Model Using Finite Element Method for Moisture Condensation Zone in Bentonite-Bonded Silica Sand
2024
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
DOI :
10.1007/s11665-024-09265-1
|
| 2. |
Experimental Construction and Validation of Revised Drucker–Prager Model Using Finite Element Method for Moisture Condensation Zone in Bentonite-Bonded Silica Sand
2024
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
Journal of Materials Engineering and Performance
DOI :
10.1007/s11665-024-09265-1
|
| 3. |
Novel Control Factor for Tensile Strength and Solidification Cracking in Partially Solidified Al-Mn-Cu Alloy Based on Campbell's Model with Fe-Rich Intermetallic Compounds
2024
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
DOI :
10.1007/s11661-024-07564-9
|
| 4. |
Clarification of the mechanism of hot tearing susceptibility reduction by Sr addition in Al-Mg-Mn-based die casting alloy using acoustic emission method
2023
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
KEIKINZOKU/JOURNAL OF JAPAN INSTITUTE OF LIGHT METALS
DOI :
10.2464/jilm.73.315
|
| 5. |
Proposition of new yield criterion for green sand mold and its experimental validation by FEM stress analysis of triaxial compression test
2023
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
Journal of Materials Processing Technology
DOI :
10.1016/j.jmatprotec.2023.118020
|
| 6. |
Development of High-Ductility and Low-Hot-Tearing-Susceptibility Non-heat Treatment Al-Mg-Mn-Based Die Casting Alloy for Automotive Structural Parts
2023
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
INTERNATIONAL JOURNAL OF METALCASTING
DOI :
10.1007/s40962-023-01047-0
|
| 7. |
An analysis of the effect of syringe barrel volume on performance and user perception
2023
Author(s) : Raja Ariffin Bin Raja Ghazilla, Azuddin Bin Mamat, Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
MEDICINE
DOI :
10.1097/MD.0000000000033983
|
| 8. |
Proposition of new yield criterion for green sand mold and its experimental validation by FEM stress analysis of triaxial compression test
2023
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
DOI :
10.1016/j.jmatprotec.2023.118020
|
| 9. |
Effects of Preheating on Microstructural and Mechanical Properties of Friction Stir Welded Thin Low Carbon Steel Joints
2023
Author(s) : Farazila Binti Yusof, Mohd.fadzil Bin Jamaludin, Mohd Ridha Bin Muhamad @ Mohd Ata'illah, Muhammad Khairi Faiz Bin Ahmad Hairuddin, Sufian Raja Source :
JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME
DOI :
10.1115/1.4055909
|
| 10. |
Novel Algorithm for Mobile Robot Path Planning in Constrained Environment
2022
Author(s) : Erma Rahayu Binti Mohd Faizal Abdullah, Mohd Nashrul Bin Mohd Zubir, Muhammad Khairi Faiz Bin Ahmad Hairuddin, Mohammed Abdo Hashem Ali Source :
CMC-COMPUTERS MATERIALS & CONTINUA
DOI :
10.32604/cmc.2022.020873
|
| 11. |
Development of High Ductility and Low Hot Tearing Susceptibility Non-Heat Treatment Al-Mg-Mn-Based Die Casting Alloy for Structural Parts of Automobile
2022
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
JOURNAL OF JAPAN FOUNDRY ENGINEERING SOCIETY
DOI :
10.11279/jfes.94.690
|
| 12. |
Influence of solid cohesion on viscous properties in Norton law for aluminum alloys during partial solidification
2022
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
DOI :
10.1016/j.msea.2021.142339
|
| 13. |
The hypodermic syringe performance based on the ISO 7886-1:2017: A narrative review
2022
Author(s) : Raja Ariffin Bin Raja Ghazilla, Azuddin Bin Mamat, Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
MEDICINE
DOI :
10.1097/MD.0000000000031812
|
| 14. |
Evaluation of Ejection Force for Die Castings by FEM Thermal Stress Analysis with Elasto-Plastic-Creep Model
2022
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
MATERIALS TRANSACTIONS
DOI :
10.2320/matertrans.F-M2021852
|
| 15. |
Effect of Sand Mold Constraint on Warpage Deformation of Lamellar Graphite Gray Cast Iron and Prediction by Elastoplastic-Creep Finite Element Analysis
2021
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
DOI :
10.1007/s11665-021-05716-1
|
| 16. |
Measurement of viscous properties on Al-5mass%Mg alloy in semi-solid state by tensile test with high-frequency induction heating
2021
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
Journal of Japan Institute of Light Metals
DOI :
10.2464/jilm.71.1
|
| 17. |
Effect of Sand Mold Constraint on Warpage Deformation of Lamellar Graphite Gray Cast Iron and Prediction by Elastoplastic-Creep Finite Element Analysis
2021
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
DOI :
10.1007/s11665-021-05716-1
|
| 18. |
Novel Algorithm for Mobile Robot Path Planning in Constrained Environment
2021
Author(s) : Mohd Nashrul Bin Mohd Zubir, Muhammad Khairi Faiz Bin Ahmad Hairuddin, Erma Rahayu Binti Mohd Faizal Abdullah, Mohammed Abdo Hashem Ali Source :
CMC-COMPUTERS MATERIALS & CONTINUA
DOI :
10.32604/cmc.2022.020873
|
| 19. |
Viscosity Properties Prediction of Semi-Solid Aluminum Alloys Using Finite Element Analysis Based on Quenched Solidified Structure, and Experimental Validation
2020
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
Materials Transactions
|
| 20. |
Evaluation of Ejection Force for Die Castings by FEM Thermal Stress Analysis with Elasto-Plastic-Creep Model
2020
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
Journal of Japan Foundry Engineering Society
DOI :
10.11279/jfes.92.583
|
| 21. |
Low temperature Cu–Cu bonding by transient liquid phase sintering of mixed Cu nanoparticles and Sn–Bi eutectic powders
2017
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
Journal of Materials Science: Materials in Electronics (JMSE)
DOI :
10.1007/s10854-017-7554-6
|
| 22. |
Low temperature and low pressure bonding of plateless Cu–Cu substrates by Ag-based transient liquid phase sintering
2017
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
Journal of Materials Science: Materials in Electronics (JMSE)
DOI :
10.1007/s10854-017-6674-3
|
| 23. |
Analysis of partially pulsating fatigue process on carbon steel with microstructural observation
2016
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin Source :
Materials Science & Engineering A
|
PROCEEDING
| NO | DETAILS OF PROCEEDING |
|---|---|
| 1. |
Development of High-Ductility and Low-Hot-Tearing-Susceptibility Non-heat Treatment Al-Mg-Mn-Based Die Casting Alloy for Automotive Structural Parts
2023
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin |
| 2. |
Relationships of design parameters and the cooling performance of the spiral-fin heatsink
2021
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin |
| 3. |
Heatsink design using spiral-fins considering additive manufacturing
2019
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin |
| 4. |
On Design Optimization of Heat Sinks with Curvature Considerations for Additive Manufacturing
2018
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin |
| 5. |
Low temperature and low pressure fluxless Cu-Cu bonding by Ag-based transient liquid phase sintering for high temperature application
2017
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin |
| 6. |
Sn-Bi added Ag-based transient liquid phase sintering for low temperature bonding
2017
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin |
| 7. |
Low temperature, low pressure, fluxless and plateless Cu-Cu bonding by Cu nano particle transient liquid phase sintering
2017
Author(s) : Muhammad Khairi Faiz Bin Ahmad Hairuddin |
RESEARCH PROJECT
| GRANT | PROGRESS | STATUS |
|---|---|---|
|
Enhancing Mechanical Properties and Thermomechanical Reliability of Pb-Free Solder with Malaysia-Mined Rare Earth Elements for Sustainable Green Energy Technology
Researcher(s) : Dr. Goh Yingxin, Prof. Dr. Andri Andriyana, Professor Ir. Dr. Wong Yew Hoong, Dr. Hijaz Kamal Bin Hasnan, Makoto Yoshida, Eu Poh Leng |
|
new |
|
Digital Image Correlation Technique For Mechanical Properties Acquisition And Thermomechanical Assessment Of Thin Sintered Copper Nanoparticles Layer
Researcher(s) : Associate Prof. Dr. Farazila Binti Yusof, Professor Ir. Dr. Wong Yew Hoong, Farah Liana Binti Mohd Redzuan, Makoto Yoshida |
|
on going |
|
Rolling with Sustainability: Transforming Campus Paper Waste into Water-Soluble Toilet Rolls
Researcher(s) : - |
|
on going |
RESEARCH COLLABORATOR
| GRANT | PROGRESS | STATUS |
|---|---|---|
|
Formulated Metal Oxides For Microstructure-properties Relationship Digitization Through Machine Learning For Industry 4.0
|
|
on going |
|
Wp2: Mineral Carbonation For Carbon Capture And Utilisation In Malaysian Basalts Formation And Concrete
|
|
on going |
|
Development Of A Dedicated Wire-arc Additive Manufacturing (waam) Work Cell For The Production Of Near-net Shaped Large Sized Lightweight Metal Components
|
|
end |